FALTA poco! #PorMenosChatarrahoja verde
Solo faltan 52.409 soluciones y llegaremos a los 500.000 articulos que no se convirtieron en CHATARRA o BASURA!!!
 

ricoth ft6645 error sc542

Seguir
estimados colegas saludes, necesito manual de servicio de Ricoth ft6645 error sc542 ella como que quisiera arrancar pero me tira el error y no se a que se refiere, es primera ves que estoy trabajando con ricoth mi especialidad es en canon, tishiba y minolta si alguien tiene el manual y me lo puede facilitar se lo agradeceria.

tengo manuales de fotocopiadoras Canon y Minolta si se les afrece alguno estan a la disponibilidad.

si me solicitan algun manual por favor especificar el modelo

titulo editado, debes poner marca modelo y requerimiento[/color:bc108906d1]

    3 Soluciones propuestas

    hola colega ,la maquina tiene problema en la unidad fusora ,posiblemente lampara,termistor,termofuse etc revisa esa parte

    te envio el listado de errores

    Code Description
    101 Exposure lamp
    103 Power frequency problem
    104 Exposure lamp
    120 Scanner home problem
    121 Scan home problem
    125 Scanning too slow
    126 Scanning too fast
    127 Scan drive problem or encoder
    140 Lens home problem (vertical)
    141 Lens home problem (vertical)
    142 Lens home problem (horizontal)
    143 Lens home problem (horizontal)
    144 3rd scan sensor problem
    145 3rd scan sensor problem
    146 Magnification problem
    190 Optics thermistor open circuit
    191 Scan motor thermistor
    302 Charge corona short
    303 Charge corona cleaner problem
    341 Developer motor drive problem
    342 Toner disposal motor drive problem
    343 Vsp. Problem. Image density sensor problem
    351 Vsg. Problem. Higher than 4.3 volts. Image density sensor problem
    352 Toner sensor problem during developer calibration
    353 Vsp. Problem. Image density sensor, drum bias or HVT
    354 Vsg. Problem. Same as 353
    355 Toner density sensor problem. Vtd problem. Undertoned
    356 Toner density sensor problem. Vtd. Problem. Overtoned
    357 Vsp problem. Image density sensor, drum
    358 Vsp problem. Image density sensor, drum, toner dust
    361 Drum potential sensor calibration during process control setup
    364 Vd problem. Drum potential sensor, drum or charge corona
    365 V1 problem. Drum potential sensor, drum, charge corona, dirty optics
    402 Transfer, transfer belt, HVT
    440 Main motor speed problem
    442 Drum thermistor
    500 Bypass feed
    501 Paper feed motor
    502 1st lift motor
    503 2nd lift motor
    504 3rd lift motor
    506 LCT motor
    507 LCT feed motor
    508 Tandem fence motor
    510 Tandem side home sensor
    511 Tandem side home sensor
    520 Duplex/fuser drive motor problem
    522 Jogger home sensor
    523 Jogger home sensor
    541 Fuser thermistor
    542 Fuser does not warm-up
    543 Fuser temperature too high. Monitored by main board
    544 Fuser temperature too high. Monitored by optics board
    545 Low fuser temperature. Monitored by main board
    546 Low fuser temperature. Monitored by optics board
    547 Fuser lamp won't shut off
    548 Erratic fuser temperature
    600 Communication problem between main board and operation board
    601 Communication problem between main board and optics board
    602 Communication problem between main board and high voltage unit
    603 Main board problem
    620 Communication problem between main board and document feeder boards
    621 Communication problem between main board and sorter staplers or finisher
    700 DJF/RDH feed motor
    701 DJF/RDH transport belt problem
    702 DJF exit or RDH inverter motor
    703 RDH exit motor problem
    730 Sorter/stapler or finisher transport motor
    731 Bin lift motor
    732 Tray shift motor
    733 Tray shift lift motor
    735 Duplex jogger motor
    737 Gripper motor
    738 Staple motor
    740 Staple drive motor
    741 Bin rear plate motor (stapler)
    742 Finisher stack feed motor
    900 Total counter
    901 Total counter
    SC Full waste toner bottle. Technician must empty this. Emptying the waste toner and reinstalling the bottle will clear this


    saludos
      boy a revisar esas partes gracias por tu ayuda, luego te cuento
        si por algun motivo sacastes la uf la maquina detecta que se quema la lampara por ejemplo o mas comun que sacas la unidad de fusion con el switch de la puerta puenteado!, hasta que no la reseteas siempre aparece el mismo error aunque ya hayas testeado que todo este en condiciones y asi lo esté

        la solucion: una vez que chequeas que esta todo en condiciones(lampara, termistor, termoswitch, conector, etc..) entras y salis del modo de servicio (el clear 107 stop x3 seg)la apagas , la prendes y ya esta